View MIC23201YML_7767204.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mic23201 2mhz pwm 2a buck regulator with hyper speed control? hyper speed control is a trademark of micrel, inc. mlf and micro leadframe are registered trademark amkor technology inc. micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com august 2012 m9999-082912-a general description the mic23201 is a high efficiency 2mhz 2a synchronous buck regulator with hyper speed control. micrel?s hyper speed control provides ultra-fast transient response which is perfectly suited for supplying processor core voltages. an additional benefit of this proprietary architecture is very low output ripple voltage throughout the entire load range with the use of small output capacitors. the tiny 3mm x 3mm mlf ? package saves precious board space and requires only three external components. the mic23201 is designed for use with a very small inductor, down to 1h, and an output capacitor as small as 22f that enables a total solution size, less than 1.5mm height. the mic23201 provides a constant switching frequency around 2mhz while achieving peak efficiencies up to 90%. the mic23201 is available in 10-pin 3mm x 3mm mlf package with an operating junction temperature range from ?40 ? c to +125 ? c. datasheets and support documentation can be found on micrel?s web site at: www.micrel.com . features ? input voltage: 2.7v to 5.5v ? 2a output current ? up to 90% peak efficiency ? programmable soft-start ? power good indicator ? 2mhz switching frequency ? safe for pre-biased output ? ultra fast transient response ? low voltage output ripple, 16mv at full load ? fully integrated mosfet switches ? 0.01a shutdown current ? thermal shutdown and current limit protection ? output voltage as low as 0.95v ? 10-pin 3mm x 3mm mlf ? ?40 ? c to +125 ? c operating junction temperature range applications ? low voltage point of load ? blu ray dvd players ? networking equipment ? set top boxes ____________________________________________________________________________________________________________ typical application efficiency (v in = 3.3v) vs. output current 0 10 20 30 40 50 60 70 80 90 100 0 0.6 1.2 1.8 2.4 3 output current (a) efficiency (%) 2.5v 1.8v 1.5v 1.2v 0.95v v in = 3.3v
micrel inc. mic23201 august 2012 2 m9999-082912-a ordering information part number marking code nominal output voltage package junction temp. range lead finish MIC23201YML 201a adj 10-pin 3mm x 3mm mlf -40 ? c to +125 ? c pb-free notes: 1. other options available. contact micrel for details. 2. mlf is green rohs compliant package. lead fi nish is nipdau. mold compound is halogen free. pin configuration 10 pin 3mm x 3mm mlf (ml) (top view) pin description pin number pin name pin function 1 sw switch output: internal power mosfet output switches. 2 en enable input: logic high enables operation of the regulator. logic low will shut down the device. do not leave floating. 3 sns sense input: connect to v out as close to output capacitor as possible to sense output voltage. 4 fb feedback input: the fb pin is regulated to 0.62v. connect a resistor divider from the output to ground to set the output voltage. 5 pg power good output: open drain output for the powe r good indicator. place a resistor between this pin and a voltage source to detect a power good condition. 6 ss soft start: place a capacitor from ss pin to ground to program the soft start time. do not leave this pin floating. minimum of 100pf c ss is required. 7 agnd analog ground: connect to central ground poi nt where all high current paths meet (c in , c out , pgnd) for best operation. 8 svin signal input voltage: this pin is connected externally to the vin pin. a 2.2f ceramic capacitor from the svin pin to agnd must be placed next to the ic. 9 vin power supply input voltage: the vin pin is the input supply to the internal p-channel power mosfet. a 22f ceramic is recommended for bypassing at vin pin. 10 pgnd power ground. ep epad thermal pad. it must be connected to pgnd on the pcb to improve the thermal performance.
micrel inc. mic23201 august 2012 3 m9999-082912-a absolute maximum ratings (1) supply voltage (vin, svin)???????????... ..6v sense (v sns ).. ..................................................................6v power good (pg)??................................................. ....6v output switch voltage ???????????..??.6v enable input voltage (v en )............................... -0.3v to vin storage temperature range??????-65 ? c to +150 ? c esd rating (3) ??????????????????.1kv operating ratings (2) supply voltage (vin) ... ??????????..2.7v to 5.5v enable input voltage (v en ) .. ?????????.0v to vin output voltage range (v sns ) ???????.0.95v to 3.6v junction temperature range (t j ) .... ?.-40 ? c ? t j ? +125 ? c thermal resistance 3mm x 3mm mlf-10 ( ? ja ) .............................60.7 ? c/w 3mm x 3mm mlf-10 ( ? jc ) .............................28.7 ? c/w electrical characteristics (4) t a = 25c; vin = v en = 3.3v; l = 1.0h; c out = 22f unless otherwise specified. bold values indicate ?40c t j +125c, unless noted. parameter condition min typ max units supply voltage range 2.7 5.5 v under-voltage lockout threshold v in rising 2.45 2.55 2.65 v under-voltage lockout hysteresis 200 mv quiescent current i out = 0ma , sns > 1.2 * v out nominal 1.15 3.35 ma shutdown current v en = 0v; v in = 5.5v 1.34 5 a feedback voltage i load = 20ma 0.604 0.62 0.635 v feedback bias current 1 a current limit sns = 0.9*v outnom 2.3 4.4 a v in = 3.6v to 5.5v if v outnom < 2.5v, i load = 20ma output voltage line regulation v in = 4.5v to 5.5v if v outnom 2.5v, i load = 20ma 0.3 %/v 20ma < i load < 500ma, v in = 3.6v if v outnom < 2.5v 20ma < i load < 500ma, v in = 5.0v if v outnom 2.5v 0.46 % 20ma < i load < 1a, v in = 3.6v if v outnom < 2.5v output voltage load regulation 20ma < i load < 1a, v in = 5.0v if v outnom 2.5v 0.71 % ? pwm switch on-resistance i sw = 100ma pmos i sw = -100ma nmos 0.200 0.190 ? switching frequency i out = 120ma 2 mhz maximum duty cycle v fb = 0v 80 % soft start time v out = 90%, css=470pf 300 s soft start current v ss = 0v 2.7 a power good threshold (rising) % of v nominal 85 90 95 % power good hysteresis 7 % power good delay 68 s power good pull down resistance i pg = 250a 85 ? ? enable threshold turn-on 0.5 0.9 1.2 v enable input current 0.1 2 a over temperature shutdown t j rising 160 ? c over temperature shutdown hysteresis 20 ? c notes: 1. exceeding the absolute maxi mum rating may damage the device. 2. the device is not guaranteed to function outside its operating rating. 3. devices are esd sensitive. handling precautions recommended. human body model, 1.5k ? in series with 100pf. 4. specification for packaged product only.
micrel inc. mic23201 august 2012 4 m9999-082912-a typical characteristics v in operating supply current vs. input voltage 0 10 20 30 40 50 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) supply current (ma) v out = 1.8v i out = 0a sw itching v in shutdown current vs. input voltage 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) shutdown current (a) v en = 0v feedback voltage vs. input voltage 0.600 0.608 0.616 0.624 0.632 0.640 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) feedback voltage (v) v out = 1.8v output regulation vs. input voltage 0.0% 0.2% 0.4% 0.6% 0.8% 1.0% 1.2% 1.4% 1.6% 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) output regulation (%) v out = 1.8v i out = 0a to 2a current limit vs. input voltage 0 2 4 6 8 10 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) current limit (a) v out = 1.8v enable threshold vs. input voltage 0.00 0.20 0.40 0.60 0.80 1.00 1.20 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) enable threshold (v) falling rising switching frequency vs. input voltage 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) switching frequency (khz) v out = 1.8v i out = 0a enable input current vs. input voltage 0.00 0.25 0.50 0.75 1.00 1.25 1.50 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) enable input current (a) v en = v in power good threshold/v ref ratio vs. input voltage 0 10 20 30 40 50 60 70 80 90 100 2.5 3.0 3.5 4.0 4.5 5.0 5.5 input voltage (v) v pg threshold/v ref (%) v ref = 0.62v
micrel inc. mic23201 august 2012 5 m9999-082912-a typical characteristics (continued) v in operating supply current vs. temperature 0 10 20 30 40 50 -50 -25 0 25 50 75 100 125 temperature (c) supply current (ma) v in =3.3v v out = 1.8v i out = 0a sw itching v in shutdown current vs. temperature 0 1 2 3 4 5 6 7 8 9 10 -50 -25 0 25 50 75 100 125 temperature (c) shutdown current (a) v in = 3.3v i out = 0a v en/dly = 0v v in uvlo threshold vs. temperature 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 -50 -25 0 25 50 75 100 125 temperature (c) vin threshold (v) rising falling feedback voltage vs. temperature 0.600 0.608 0.616 0.624 0.632 0.640 -50 -25 0 25 50 75 100 125 temperature (c) feedback voltage (v) v in = 3.3v v out = 1.8v i out = 0a load regulation vs. temperature 0.0% 0.2% 0.4% 0.6% 0.8% 1.0% 1.2% 1.4% 1.6% 1.8% 2.0% -50 -25 0 25 50 75 100 125 temperature (c) load regulation (%) v in = 3.3v v out = 1.8v i out = 0a to 2a line regulation vs. temperature -2.00% -1.50% -1.00% -0.50% 0.00% 0.50% -50 -25 0 25 50 75 100 125 temperature (c) line regulation (%) v in = 2.7v to 5.5v v out = 1.8v switching frequency vs. temperature 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 -50 -25 0 25 50 75 100 125 temperature (c) switching frequency (khz) v in = 3.3v v out = 1.8v i out = 0a enable threshold vs. temperature 0.70 0.80 0.90 1.00 1.10 1.20 -50 -25 0 25 50 75 100 125 temperature (c) enable threshold (v) v in = 3.3v rising falling current limit vs. temperature 0 2 4 6 8 10 -50 -25 0 25 50 75 100 125 temperature (c) current limit (a) v in = 3.3v v out = 1.8v
micrel inc. mic23201 august 2012 6 m9999-082912-a typical characteristics (continued) enable input current vs. temperature 0.00 0.20 0.40 0.60 0.80 1.00 -50 -25 0 25 50 75 100 125 temperature (c) enable input current (a) v in = 3.3v v en = v in feedback voltage vs. output current 0.600 0.610 0.620 0.630 0.640 0.650 0.0 0.5 1.0 1.5 2.0 output current (a) feedback voltage (v) v in = 3.3v v out = 1.8v line regulation vs. output current -2.00% -1.80% -1.60% -1.40% -1.20% -1.00% -0.80% -0.60% -0.40% -0.20% 0.00% 0.0 0.5 1.0 1.5 2.0 output current (a) line regulation (%) v in = 2.7v to 5.5v v out = 1.8v switching frequency vs. output current 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 0.00.51.01.52.0 output current (a) switching frequency (khz) v in = 3.3v v out = 1.8v efficiency (v in = 3.3v) vs. output current 0 10 20 30 40 50 60 70 80 90 100 0 0.6 1.2 1.8 2.4 3 output current (a) efficiency (%) 2.5v 1.8v 1.5v 1.2v 0.95v v in = 3.3v efficiency (v in = 5v) vs. output current 0 10 20 30 40 50 60 70 80 90 100 0 0.6 1.2 1.8 2.4 3 output current (a) efficiency (%) 3.6v 3.3v 2.7v 2.5v 1.8v 1.5v 1.2v 0.95v v in = 5v efficiency vs. output current 0 10 20 30 40 50 60 70 80 90 100 0 0.5 1 1.5 2 output current (a) efficiency (%) 3.3v in 5.0v in v out = 1.8v output voltage vs. load current 0.000 0.200 0.400 0.600 0.800 1.000 1.200 1.400 1.600 1.800 2.000 0.0 1.0 2.0 3.0 4.0 5.0 load current (a) output voltage (v) v in = 3.3a v out = 1.8v v out rise time vs. css 1 10 100 1000 10000 100000 1000000 100 1000 10000 100000 1000000 css (pf) rise time (s) v in = 3.3v v out = 1.8v
micrel inc. mic23201 august 2012 7 m9999-082912-a typical characteristics (continued) case temperature* (v in = 3.3v) vs. output current 0 20 40 60 80 100 0.0 0.5 1.0 1.5 2.0 output current (a) die temperature (c) v in = 3.3v v out = 1.8v case temperature* (v in = 5.0v) vs. output current 0 20 40 60 80 100 0.0 0.5 1.0 1.5 2.0 output current (a) die temperature (c) v in = 5v v out = 1.8v die temperature* : the temperature measurement was tak en at the hottest point on the mic232 01 case and mounted on a 1.4-square inch pcb (see thermal measurement s section). actual results will depend upon th e size of the pcb, am bient temperature, and proximity to other heat-emitting components.
micrel inc. mic23201 august 2012 8 m9999-082912-a functional characteristics
micrel inc. mic23201 august 2012 9 m9999-082912-a functional characteristics (continued)
micrel inc. mic23201 august 2012 10 m9999-082912-a functional characteristics (continued)
micrel inc. mic23201 august 2012 11 m9999-082912-a functional diagram figure 1. simplified mic23201 functional block diagram functional description vin the input supply (vin) provides power to the internal mosfets for the switch mode regulator along with the internal control circuitry. t he vin operating range is 2.7v to 5.5v so an input capacitor, with a minimum voltage rating of 6.3v, is recommended. due to the high switching speed, 22f bypass capacitor placed close to vin and the power ground (pgnd) pin is required. refer to the layout recommendations for details. svin the input supply (svin) provides power to internal control circuitry. this pin is connected externally to the vin pin. a 2.2f ceramic capacitor from the svin pin to agnd must be placed next to the ic. en a logic high signal on the enable pin activates the output voltage of the device. a logic low signal on the enable pin deactivates the output and reduces supply current to 0.01a. mic23201 features bu ilt-in soft-start circuitry that reduces in-rush curr ent and prevents the output voltage from overshooting at st art up. do not leave this pin floating. sw the switch (sw) connects directly to one end of the inductor and provides the current path during switching cycles. the other end of the inductor is connected to the load, sns pin and output capacitor. due to the high speed switching on this pin, the switch node should be routed away from sensitive nodes whenever possible. ss the soft start (ss) pin is used to control the output voltage ramp up time. the approximate equation for the ramp time in seconds is 270x10 3 x ln(10) x c ss . for example, for a c ss = 470pf, t rise ~ 300s. see the typical characteristics curve for a graphical guide. the minimum recommended value for c ss is 100pf. sns the sense (sns) pin is connected to the output of the device to provide feedback to the control circuitry. the
micrel inc. mic23201 august 2012 12 m9999-082912-a sns connection should be placed close to the output capacitor. refer to the layout recommendations for more details. agnd the analog ground (agnd) is the ground path for the biasing and control circuitry. the current loop for the signal ground should be separate from the power ground (pgnd) loop. refer to the layout recommendations for more details. pgnd the power ground pin is the ground path for the high current. the current loop for the power ground should be as small as possible and separate from the analog ground (agnd) loop as applicable. refer to the layout recommendations for more details. fb the fb pin is regulated to 0.62v. a resistor divider connecting the feedback to the output is used to adjust the desired output voltage. a resistor divider network is connected to this pin from the output and is compared to the internal 0.62v reference within the regulation loop. the output voltage can be programmed using the following equation: ? ? ? ? ? ? ? ? ? r2 r1 1 v v ref out where: r1 is the top resistor, r2 is the bottom resistor. the output voltage can be adjusted from 0.95v to 3.6v. pg the power good (pg) pin is an open drain output which indicates logic high when the output voltage is typically above 87% of its steady state voltage. a pull-up resistor of more than 5k ? should be connected from pg to v out .
micrel inc. mic23201 august 2012 13 m9999-082912-a application information the mic23201 is a high performance dc/dc step down regulator offering a small solution size. supporting an output current up to 2a inside a tiny 3mm x 3mm mlf package and requiring only three external components, the mic23201 is able to maintain high efficiency throughout the entire load range while providing ultra- fast load transient response. the following sections provide additional device application information. input capacitor a minimum of 4.7f ceramic capacitor or greater should be placed close to the vin pin and pgnd / gnd pin for bypassing but the recommended value of input capacitor is 22f. a x5r or x7r temperature rating is recommended for the input capacitor. y5v temperature rating capacitors, aside from losing most of their capacitance over temperature, can also become resistive at high fre quencies. this reduces their ability to filter out high frequency noise. output capacitor the mic23201 was designed for use with a minimum of 4.7f or greater ceramic output capacitor. increasing the output capacitance will lower output ripple and improve load transient response but could increase solution size or cost. the recommended value of output capacitor is 22f. a low equivalent series resistance (esr) ceramic output capacitor is recommended based upon performance, size and cost. both the x7r or x5r temperature rating capacitors are recommended. the y5v and z5u temperature rating capacitors are not recommended due to their wide variation in capacitance over temperature and increased resistance at high frequencies. inductor selection when selecting an inductor, it is important to consider the following factors (not nec essarily in the order of importance): ? inductance ? rated current value ? size requirements ? dc resistance (dcr) the mic23201 was designed for use with a 1h to 2.2h inductor. for faster transient response, a 1h inductor will yield the best re sult. for lower output ripple, a 2.2h inductor is recommended. maximum current ratings of the inductor are generally given in two methods; permissible dc current and saturation current. permissible dc current can be rated either for a 40c temperature rise or a 10% to 20% loss in inductance. ensure the inductor selected can handle the maximum operating current. when saturation current is specified, make sure that there is enough margin so that the peak current does not cause the inductor to saturate. peak current can be calculated as follows: ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? l f 2 /v v 1 v i i in out out out peak as shown by the calculati on above, the peak inductor current is inversely proportional to the switching frequency and the inductance; the lower the switching frequency or the inductance the higher the peak current. as input voltage increases, the peak current also increases. the size of the inductor depends on the requirements of the application. refer to the typical application circuit and bill of materials for details. dc resistance (dcr) is also important. while dcr is inversely proportional to size, dcr can represent a significant efficiency loss . refer to the efficiency considerations. compensation the mic23201 is designed to be stable with a 1h to 2.2h inductor with a minimum of 4.7f ceramic (x5r) output capacitor.
micrel inc. mic23201 august 2012 14 m9999-082912-a efficiency considerations efficiency is defined as the amount of useful output power, divided by the amount of power supplied. 100 ? ? ? ? ? ? ? ? ? ? ? ? in in out out i v i v % efficiency maintaining high efficiency serves two purposes. it reduces power dissipation in the power supply, reducing the need for heat sinks and thermal design considerations and it reduces consumption of current for battery powered applications. reduced current draw from a battery increases the devices operating time and is critical in hand held devices. there are two types of losses in switching converters; dc losses and switching losses. dc losses are simply the power dissipation of i 2 r. power is dissipated in the high side switch during the on cycle. power loss is equal to the high side mosfet r dson multiplied by the rms switch current squared. during the off cycle, the low side n-channel mosfet conducts, also dissipating power. device operating current also reduces efficiency. the product of the quiescent (operating) current and the supply voltage represents anot her dc loss. the current required driving the gates on and off at a constant 2mhz frequency and the switching transitions make up the switching losses. all but the inductor losses are inherent to the device. in which case, inductor selection becomes increasingly critical in efficiency calculations. as the inductors are reduced in size, the dc resistance (dcr) can become quite significant. the dcr losses can be calculated as follows: p dcr = i out 2 x dcr from that, the loss in efficiency due to inductor resistance can be calculated as follows: 100 p i v i v 1 loss efficiency dcr out out out out ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? efficiency loss due to dcr is minimal at light loads and gains significance as the l oad is increased. inductor selection becomes a trade-off between efficiency and size in this case. thermal considerations the mic23201 is provided in a 3mm x 3mm mlf package ? a package that has very good thermal- performance this package maximizes heat transfer from the junction to the exposed pad (ep), which connects to the ground plane. the size of the ground plane attached to the exposed pad determines the overall thermal resistance from the junction to the ambient air surrounding the printed circuit board. the junction temperature for a given ambient temperature can be calculated using: t j = t amb + p diss ? ? ja where: ? p diss is the power dissipated within the mlf package. ja is a combination of junction-to-case thermal resistance ( jc ) and case-to-ambient thermal resistance ( ca ), since thermal resistance of the solder connection from the epad to the pcb is negligible, so ja = jc + ca . ? t amb is the operating ambient temperature. thermal measurements measuring the ic?s case temperature is recommended to ensure it is within its operat ing limits. although this might seem like a very elementary task, it is easy to get erroneous results. the most common mistake is to use the standard thermal couple that comes with a thermal meter. this thermal couple wire gauge is large, typically 22 gauge, and behaves like a heatsink, resulting in a lower case measurement. two methods of temperature measurement are using a smaller thermal couple wire or an infrared thermometer. if a thermal couple wire is used, it must be constructed of 36 gauge wire or higher then (smaller wire size) to minimize the wire heat-sinking effect. in addition, the thermal couple tip must be covered in either thermal grease or thermal glue to make sure that the thermal couple junction is making good contact with the case of the ic. omega brand thermal couple (5sc-tt-k-36-36) is adequate for most applications. wherever possible, an infrared thermometer is recommended. the measurement spot size of most infrared thermometers is too large for an accurate reading on a small form factor ics. however, an ir thermometer from optris has a 1mm spot size, which makes it a good choice for measuring the hottest point on the case. an optional stand makes it easy to hold the beam on the ic for long periods of time.
micrel inc. mic23201 august 2012 15 m9999-082912-a pcb layout guidelines warning!!! to minimize emi and output noise, follow these layout recommendations. pcb layout is critical to achieve reliable, stable and efficient performance. a ground plane is required to control emi and minimize the inductance in power, signal and return paths. thickness of the copper planes is also important in terms of dissipating heat. the 2 ounce copper thickness is adequate from thermal point of view and also thick copper plain helps in terms of noise immunity. keep in mind thinner planes can be easily penetrated by noise the following guidelines should be followed to insure proper operation of the mic23201 converter. ic ? place the ic close to the point of load (pol). ? use fat traces to route the input and output power lines. ? the signal ground pin (a gnd) must be connected directly to the ground planes. ? signal and power grounds should be kept separate and connected at only one location. input capacitor ? place the input capacitor next to the power pins. ? place the input capacitors on the same side of the board and as close to the ic as possible. ? keep both the vin pin and pgnd connections short. ? place several vias to the ground plane close to the input capacitor ground terminal. ? use either x7r or x5r dielectric input capacitors. do not use y5v or z5u type capacitors. ? do not replace the ceramic input capacitor with any other type of capacitor. any type of capacitor can be placed in parallel with the input capacitor. ? if a tantalum input capacitor is placed in parallel with the input capacitor, it must be recommended for switching regulator applications and the operating voltage must be derated by 50%. ? in ?hot-plug? applications, a tantalum or electrolytic bypass capacitor must be used to limit the over- voltage spike seen on the input supply with power is suddenly applied. inductor ? keep the inductor connection to the switch node (sw) short. ? do not route any digital lines underneath or close to the inductor. ? keep the switch node (sw) away from the feedback (fb) pin. ? to minimize noise, place a ground plane underneath the inductor. ? the inductor can be placed on the opposite side of the pcb with respect to the ic. it does not matter whether the ic or inductor is on the top or bottom as long as there is enough air flow to keep the power components within their temperature limits. the input and output capacitors must be placed on the same side of the board as the ic. output capacitor ? use a wide trace to connect the output capacitor ground terminal to the input capacitor ground terminal. ? phase margin will change as the output capacitor value and esr changes. contact the factory if the output capacitor is different from what is shown in the bom. ? the feedback trace should be separate from the power trace and connected as close as possible to the output capacitor. sensing a long high current load trace can degrade the dc load regulation. rc snubber ? place the rc snubber on either side of the board and as close to the sw pin as possible.
micrel inc. mic23201 august 2012 16 m9999-082912-a typical application circuit bill of materials item part number manufacturer description qty. c1, c2 grm31cr71a226ke15l murata (1) ceramic capacitor, 22f, 10v, x7r, size 1206 2 06035c471kat2a avx (2) grm188r71h471ka01d murata c3 c1608x7r1h471k tdk (3) ceramic capacitor, 470pf, 50v, x7r, size 0603 1 c4 ? ? not fitted (nf) 06036d225kat2a avx 1 grm188r60j225ke19d murata c5 c1608x5r0j225k tdk ceramic capacitor, 2.2 f, 6.3v, x5r, size 0603 l1 vls4012t-1r0n1r6 tdk 1h, 2.5a, 60m ? , l4.0mm x w4.0mm x h1.2mm 1 r1 crcw0201301kfked vishay/dale (4) resistor, 301k ? , size 0603 1 r2 erj-1gef1583c panasonic - ecg (5) resistor,158k ? , size 0603 1 r3, r4 crcw020110k0jned vishay/dale resistor,10k ? , size 0603 2 r5 erj-3geyj2r2v panasonic - ecg resistor, 2.2 ? , size 0603 r6 crcw020149r9fked vishay/dale resistor, 49.9 ? , size 0603 u1 MIC23201YML micrel, inc. (6) 2mhz 2a buck regulator with hyper speed control mode 1 notes: 1. murata : www.murata.com . 2. avx: www.avx.com . 3. tdk: www.tdk.com . 4. vishay: www.vishay.com . 5. panasonic: www.industrial.panasonic.com . 6. micrel, inc.: www.micrel.com .
micrel inc. mic23201 august 2012 17 m9999-082912-a pcb layout figure 11. mic23201 evaluation board top layer figure 12. mic23201 evaluation board mid-layer 1 (ground plane)
micrel inc. mic23201 august 2012 18 m9999-082912-a pcb layout (continued) figure 13. mic23201 evaluation board mid-layer 2 figure 14. mic23201 evaluation board bottom layer
micrel inc. mic23201 august 2012 19 m9999-082912-a recommended land pattern all units are in mm, tolerance ? 0.05, if not noted lp # mlf33d-10ld-lp-1
micrel inc. mic23201 august 2012 20 m9999-082912-a package information 10-pin 3mm x 3mm mlf (ml) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is belie ved to be accurate and reliable. however, no responsibility is a ssumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authori zed for use as components in life support app liances, devices or systems where malfu nction of a product can reasonably be expected to result in pers onal injury. life support devices or system s are devices or systems that (a) are in tended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support app liances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2012 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC23201YML

	To Download MIC23201YML Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .